- #Plextor px 716a manuals
- #Plextor px 716a manual
- #Plextor px 716a software
- #Plextor px 716a trial
- #Plextor px 716a professional
If a disc is warped or uneven, the laser beam will not be positioned correctly. The best reading and writing quality occurs when the angle between the disc and laser is 90 degrees. To find out, we'll take a closer look at this technology in the performance section of this review.
![plextor px 716a plextor px 716a](https://i.ebayimg.com/images/g/8OoAAOSw5D1cp14h/s-l400.jpg)
The big question here is whether or not AutoStrategy works. Most of the results it gives are pretty self explanatory.
#Plextor px 716a professional
Plextools Professional also lets you run a basic media quality check to determine whether or not you will see good results at the selected speeds. Otherwise you can view, deactivate or delete the writing strategies manually using PlexTools Professional. According to Plextor, AutoStrategy automatically erases little used entries to make room for new ones. While the PX-716A holds a maximum of 31 writing strategies, you don't have to worry about filling up the drive's memory.
#Plextor px 716a trial
AutoStrategy simply identifies the disc, pulls the writing strategy from memory and does a trial write, a process that takes about 15 seconds. With subsequent burns, the process is much faster. The first time AutoStrategy calculates a writing strategy for a disc, it can add anywhere from two and a half to four minutes to the total writing time. Once done, it will save this writing strategy to memory. During this time, AutoStrategy continually monitors the process via ROPC and PoweRec and will modify the writing strategy if need be. From here, the PX-716A will start writing the data to disc. If not, it will do a trial write and start calculating a writing strategy. AutoStrategy then checks to see if the disc's information is already stored in the drive's memory. When you insert an unknown DVD+R or DVD-R disc (rated at 4x or faster) into a drive like the PX-716A, it will read the manufacturer ID and perform an OPC, or Optical Power Calibration, test to determine the correct laser power. The way AutoStrategy works is fairly straight forward. Developed by Taiyo Yuden, AutoStrategy automatically tests and catalogs unknown media, developing a writing strategy on the fly. For this unsupported, or unknown, media there is AutoStrategy technology. While Plextor works hard to add support for as much media as they can, they can't possibly test all of it and include it in the firmware. Consisting of AutoStrategy, Intelligent Tilt and PoweRec technologies, this system works to deliver the best writing quality possible atthe highest attainable speed. With the PX-716A, Plextor has also introduced what they call their "Intelligent Recording" system. Along with features like BURN-Proof and VariRec, it supports a number advanced technologies like GigaRec, SecuRec and the Q-Check testing system. The PX-716A has many of the features found on Plextor's other drives. **The 1.05 firmware adds support for 6x DVD-R DL writing speeds. *The 1.04 firmware adds support for 8x DVD+RW, 6x DVD+R DL and 2x DVD-R DL writing speeds.
#Plextor px 716a manual
Most of the specs below have been taken from Plextor's website and the manual that came with the drive. You can also put the PX-716A into a test mode by enabling the cable select and slave jumpers (outlined in blue). By default Ultra DMA is enabled, but by setting this jumper the drive can be set to Multiword DMA. The PX-716A also has an extra jumper (outlined in red) that can be used to disable the drive's Ultra DMA support. The connector on the far left is the digital audio output. Next to the jumper block is the analog audio connector. Starting from the left of the IDE connection you'll see the jumper switch for master, slave and cable select. While the vent along the top has been expanded a little, the rear of the PX-716A is otherwise very similar to Plextor's other ATAPI drives.By looking at the picture below you can see the drive's IDE interface, power connection and audio output connectors. Like with Plextor's other drives, you can determine the PX-716A's writing speed by monitoring the blink rate of the LED. The PX-716SA also has a single LED, which does double duty for both reading and writing activities.This LED lights up yellow when reading, ejecting or initializing a disc, green when its Buffer Under Run Proof is working, and amber when writing. Along with the large "Plextor" logo, you can see a few showing off its support for DVD+R DL, DVD-R/RW and Ultra Speed CD-RW media. Like its predecessor, the PX-716A also has its share of logos. While there are a few cosmetic differences, both drives share the same basic design including the black stripe along the front of the tray. It was also manufactured in China and had a TLA# of "0202".For this review we used firmware versions 1.03 and 1.04.įrom the front, the PX-716A looks very similar to Plextor's 12x DVD±RW drive, the PX-712A. The drive Plextor sent us for this review was manufactured in November of 2004 and had firmware version 1.02.
#Plextor px 716a software
![plextor px 716a plextor px 716a](https://i.ebayimg.com/images/g/HvUAAOSwvWNgLrrY/s-l400.jpg)
#Plextor px 716a manuals
Plextor PX-716 Installation And Users Manuals.